Swift Carbon 620SEELECTRIC R/C HELICOPTERKit Instruction ManualCentury Helicopter ProductsDesigned and Developed in USA2nd Edition May 2008 All rights
Main Frame Assembly6. Assembly InstructionsTHREAD LOCKBH Spacer Plate (CNE590)Canopy Standoff (CNE501A)Washer M3X5x.5 (CNLR1003)Ball Link (CNLR1011)C
Set Screw M3X4(CNM3X4SS)Bearing M3X9 (CNBB0930)Linkage Ball(CNLR1013)M3 LocknutTail Gear Box Assembly6. Assembly InstructionsTHREAD LOCKBM3 LocknutThr
Bearing 10x18x5 (CNBB1019)Main Gear Hub Spacer (CNE592A)Auto-rotation Hub and Bearing(CNE510B)Bevel Head Cap Screw(CNM3X8FHCS)Main Shaft(CNE508SLA)M3
Tail Belt Drive(CN531A)Tailboom(CNE532A)M3 LocknutLower Transmission Case(CNE542)M4x4 Set ScrewBearing 4x10x4(CNBB4102)Transmission Gear(CNE533)M3X4 S
Tail Component Assembly6. Assembly InstructionsCNC Tail Boom Clamp(CNE567S) Rudder Pushrod Guide(CNE534)Tail Servo Mount(CNE544)Tailboom(CNE532A)Self
Cap Screw M3X18(CNM3X18CS)Set Screw M3X4(CNM3X4SS)Landing Skids(CNE513)Hint: Place strut into a cup of warm water, if skid does not slide through the
1) Align the mounting posts from the front transmission gearbox with the mounting posts at the rear of the main frame. The horizontal n on the tail b
Linkage: bell mixer to swashplate(2) = 100mmLinkage: ybar control arm to washout arm(2) = 53mmLinkage: bell mixer to seesaw(2) = 23mmLinkage: Aileron
There are three servos that are mounted on the left and right main frames. They work together to tilt the swashplate producing the collective pitch,
Linkage for Rudder servo:Preset length by factory.CCPM Servo Guidelines8. Installing and Adjusting Control ComponentsThe goal in the end after all the
1. IntroductionCongratulations on your purchase of Century Helicopter Product’s Swift Carbon 620SE Kit. The Swift Carbon 620SE is a high performance
(1) Dry t the pinion gear to the main motor prior to mounting. Make sure the main motor gear rides in line with the main gear on the Swift.The key t
9. Final PreparationsPreparing, Mounting & Tracking The Main Rotor BladesThe Main Rotor Blades are not included in Swift Carbon 620 kit. Please r
(1) The Swift Carbon 620 does not come with main rotor blades. Please refer to the instructions included with your blades (must be purchased separete
Final Adjustments - Radio Setup10. Setup and AdjustmentNow that the servo installation into the helicopter is nished the following pages should be re
Final Adjustments - Tail Rotor Setup11. Final PreparationsGyro Gain AdjustmentThe gyro assists in holding the tail rotor, actually compensating for ch
12. Pre-FlightBasic HoveringWhen all is set, ready and checked, attach your training gear/pod and plug in your battery.Place the helicopter pointing i
CNE601620 Canopy Stand-offs & GrommetsCNE502CCPM Bellcrank SetCNE608620 Solid Main ShaftCNE610Main Gear With Auto-rotation HubCNE610AMain Gear Onl
CNE679620 Carbon Main Shaft Supports (2)13. Replacement PartsCNE674620 Carbon Main Frames(Left and Right)CNE563 CNC Machined Motor MountCNE675620 Fro
HW3098ASteel Tail Rotor HubHI3096BTail Blade GripsHI309985mm Tail Rotor BladesCNE551A620 Decal Set14. Replacement PartsCNBB364Bell Mixer Bearing (4)CN
Use this table as a guide, your setup and ight conditions will make these results uctuate.For ultimate performance with head speeds reaching close t
2. Battery Warnings & SafetyFor Lithium Polymer and NiMH/NiCD cell or battery packs purchased.1. Never fast-charge any battery type unattended.2.
Notes
3. Required Items for OperationPart#CN2015 Hardened Tip Hex Screw Driver SetPart#CN2026 Pitch Gauge with Paddle GaugePart#CN2034A 150 Curve Tip B
5. SafetyBefore ying, please check to make sure no one else is operating on the same frequency.Before ight, please check if the batteries or transmi
OILAdd a small amount of Synthetic Hydro Carbon GreaseThrust Bearing(CNBB6138T) Linkage Ball (CNLR104) Cap Screw M3X16
6. Assembly InstructionsHead BlockButton Head M3X6(CNM3X6BH) Linkage Ball (CNLR1014) Seesaw Offset Plate(CNE519A)CNC Seesaw(CNE564S)Bearing 3X10x4
Washout Base(CNE516)Linkage Ball (CNLR1014) CNC Washout Control Arm(CNE560) Bearing 3X6x2.25 (CNBB36)Cap Screw M3X12 (CNM3X12CS) Flat Washer M3
Upper Bearing Block Assembly6. Assembly InstructionsCF Servo Plate(CNE573A)CNC Standoff (CNE589)It is recommended to attach the servo to the carb
Commentaires sur ces manuels